| RWO-Plus-HGP
Firmware Release Notes: |
- 11/20/2006
Version 1.13R
- Added
support for Dial on Demand in built in PPPoE Client.
- Fixed
an error where Site Survey would return blank page under certain
circumstances
- Bug:
Radius support is broken in 1.13R, will fixed in next release
- 8/22/2006
Version 1.12R2
- Added
support for MSCHAP, CHAP, MPPE authorization types in PPPoE
client.
- Added
Supported Data Rates option.
- Greatly
improved QOS features to allow low latency (ie. VOIP) traffic
prioritization.
- Fixed
Site Survey so it correctly shows scanned Access Points that
are not broadcasting ESSID.
- Fixed
RTS/CTS works as expected.
-
Please note - if you are using the device in AP mode with
QOS enabled it may be necessary to re-enter your QOS entries
configuration after upgrade to 1.12R for proper operation.
- 5/7/2006
Version 1.11R
- Added
support for new hardware revisions.
- Added
packets per seconds graph in Access Point mode.
- Fixed
bug preventing NAT Router/Access Point mode operating correctly.
- Fixed
bug in SNMP daemon causing the daemon to stop responding to
queries after some time.
- 4/7/2006
Version 1.10R
- Fixed
problem with firewall not working correctly in bridge mode.
- Added
support for synchronizing system time with remote NTP server.
- Added
support for user selectable ethernet port speed.
- Added
built in traceroute command.
- Added
built in ping command.
- 3/10/2006
Version 1.09R3
- Fixed
problem with routing mode unit could reboot frequently.
- 2/22/2006
Version 1.09R2
- Fixed
problem with fixed data rate settings not working correctly.
- Fixed
problem with PPPoE packets not being forwarded correctly.
- Added
support for Radius Server Authorization.
- Added
support for PPtP Client Authorization.
- Added
Wireless MAC Cloning option.
- Fixed
RWO-Reset support.
-
1/4/2006
Version 1.08R
- Fixed
problem with SNMP not working properly.
- Added
MAC Address Cloning option where device operating in bridge
mode as Access Point Client will use first MAC address seen
on ethernet port as its own.
- Added
Default Password setting which is used to reset device to
factory default settings using RWO Reset software.
- Added
concurrent DHCP server/client option where in Router/NAT
Router mode RWO-Plus-HPG device uses DHCP client to obtain
IP address for the wireless interface, while providing DHCP
leases to clients on the wired interface at the same time.
- Added
WPA/TKIP authorization support.
- Added
TFTP firmware upgrade support. You can upgrade the firmware
using TFTP client that allows configuration of remote filename
(http://www.winagents.com/downloads/tftp.exe for Windows
or generic Linux tftp client). To upgrade the firmware using
TFTP from Windows box please use following command at the
command prompt:
-
tftp -i -s -t60 <ip_address> PUT <firmware_filename.bin>
<login>_<password>
- For
authorization purposes admin login and password are
sent as remote filename with '_' between them
-
11/28/2005
Version 1.07R4
- Fixed
problem with NAT Router mode not working correctly.
- Fixed
problem with WEP encryption not working in WDS mode.
-
11/15/2005
Version 1.07R2
- Fixed
problem with reset to default settings procedure not working
correctly.
- General
performance and stability increase.
-
10/31/2005
Version 1.06R
- Fixed
problem with WEP40 and WEP128 not passing traffic correctly
- Added
Port Forwarding Support (NAT Router mode only)
- Please
note: After upgrade to the 1.06R firmware from the prior
version, first time after reboot it will take approximately
three minutes for the device to fully boot up. This behavior
is expected.
|
|
